+7 (499) 702-01-13
+7 (499) 702-03-59
Пн-Пт с 9:00 до 18:00

Схема BOSCH GBH 2-24 DSE GBH 2-24 DSE (0611228643)

2 Field 220-230V
3/60 Fan GRAY
4 Switch
5 Power supply cord CN 4,15m 2 x 1,0mm H07 RN-F
6 Grommet Ø7,3-Ø8,6x76 MM
7 Cable Clip
9 Manufacturer\'s nameplate
10 Reference Plate
12 Suppression Filter
13 groove ball bearing 7x19x6
14 groove ball bearing 9x24x7
16 Brush Holder
18 Air-Deflector Ring
22 Cylindrical Gear Z=50
24 Toothed Shaft Z=3/9
26 Hammer Piston
27 Striker
28 Striker Pin
29 Piston Pin
31 Protective Grille
34 Protective Cap L=17 MM, SDS-PLUS
35 Rubber Ring
37 Damping Bushing
38 Supporting Disc
41 Shim washer 1,2 MM THICK
42 Plain bearing
43 Tab Washer
44 Switching Element
45 Switch Spring
46 Driver Pin
48 Holding Plate
49 Switch Button RED
60 Needle-Roller Bearing
61 Needle bearing
62 Needle bearing
63 Needle bearing
64 Needle-Roller Assembly
65 Plain bearing
67 groove ball bearing
70 Shaft Seal
71 Scraper
72 O-Ring 24,0x2,5 MM
73 O-Ring
74 O-Ring 11,0x3,5 MM
75 O-Ring 18,0x3,5 MM
76 O-Ring 10,5x2,7 MM
77 O-Ring 60,0x3,0 MM
80 Compression Spring
81 Compression Spring
83 Compression Spring
85 Retaining ring
86 Retaining ring
87 Retaining ring DIN 7993-A22
88 Roller
89 Ball DIN 5401-Ø7MM-III-ST
90 Tapping Screw 4,8x78 MM, TORX T-20
91 Lens Head Screw 4x32
92 Torx Oval-Head Screw 4x20
93 Tapping Screw DIN 7971-ST2,9x9,5-F
94 Recessed-Head Screw DIN 7981-ST3,5x9,5-F
95 Socket head cap screw M3x6,5-4.8
96 Tapping Screw DIN7981-ST3,9x13-C-Z
101 Suppression Filter L=55 MM WHITE
102 Cable L=130 MM WHITE
180 Sticker
700 Drill Chuck Shank 1/2\" SDS-PLUS
700/20 Countersunk-Head Screw M6x27 LEFTHAND THREADS
701 Chuck
701/700 Chuck Wrench SG2
711 Parts Set
711/10/2 Retaining ring
755 Angle Drill Head SDS-PLUS
801 Motor Housing
803 Armature With Fan 220-230V
811 Carbon-Brush Set
819 Gear Housing BLACK
820 Intermediate Flange
821 Ratchet Sleeve SDS-PLUS
821/01 Ratchet Sleeve SDS-PLUS
822 Auxiliary Handle Ø43 MM
822/120 Auxiliary Handle M8
822/124 Clamping Band Ø43 MM
822/125 T-Head Bolt M8x40 MM
822/802 index turning toolholder Ø43 MM
823 Gear Sleeve Z=26/6
826 Toothed Shaft Z=3/9
830 Drive bearing
832 Clamp Handle BLACK
833 Protection Sleeve SDS-PLUS
847 Guide Ring
879 Depth-Gauge SW 6x210 MM
888 Nameplate 26x42 MM