+7 (499) 702-01-13
+7 (499) 702-03-59
Пн-Пт с 9:00 до 18:00

Схема HUSQVARNA CTH 184T (96051010800) 08 Дека, корпус подшипника вала, вал привода ножей, ремень привода ножей

1 Deck Weldment
2 Palnut 1/4
3 Nut Lock Hex Flange 5/16 - 18
5 Bolt 5/16-18
11 Screw Thd Roll 1/4 - 20 X 5/8
13 Bolt Carr Sh 3/8 - 16 X 1-1/2 Gr. 5
14 Keeper Belt Idler
16 Nut Lock FlG 3/8 - 16 unc
17 Nut Flange Lock Top
18 Washer Spacer Mandrel
19 Bearing Ball Mandrel
20 Screw Thread Roll
23 Screw Thdrol 3/8 - 16 X 1-3/4
27 V-Belt Drive
32 Spring Drive
33 Mandrel Asm. Tall
34 Shaft Asm Mndrl N/Greaseable38
35 Blade Mower LH
36 Bolt/Washer Asm 7/16 - 20 unf
42 Screw 5/16-18 x 3/4
43 Pulley Mandrel
45 Mandrel Asm. Short
72 Chute Upper
75 Pulley Idler Flat
76 Washout Port
84 Keeper Belt LH Mandrel
85 Blade Mower RH
86 Bolt 3/8-24 x 1.50 Gr. 8
87 Washer Lock Hvy. 3/8
88 Washer Hard
91 Washer 13/32 x 1-1/4 x 12 Ga.
94 Bracket Clutch Cable
95 Screw 3/8-16 x 3/4
96 Spacer
97 Shield Idler Mower
98 Stud Fastener
99 Arm Suspension Mower Rear
100 Bolt Shoulder
101 Nut Crownlock 9/16 - 18 unc
102 Spacer Bearing Swing Plate
104 Mandrel Cover RH
105 Mandrel Cover LH
110 Gear Output
111 Gasket Gearcase
112 Shaft Gearcase Adapter
113 Plug Oil
114 Valve Relief
115 Screw Torx #10-24 x 1
116 Bolt 1/4-20 x 1.75 Gr. 5
117 Nut Hex Flange 1/4-20 unc
118 Arm Clutching
119 Gearcase Subasm
120 Keeper Belt RH
121 Washer
124 Non Greasable Mandrel Shaft
125 Bracket Idler Chassis
127 Bolt Shoulder 3/8-16 x 3-5/8 Gr. 5
128 Wheel Gauge
129 Rod Anti-Sway
130 Washer 13/32 x 13/16 x 12 Ga.
131 Pin Cotter 5/16 Bow Tie Lock
143 Door Mulch
144 Pin Hinge
145 E-Ring 5/16\"
146 Spring
154 Screw Thd Roll 1/4-20 x 1/2
159 Plate 107 CRD LH Side
160 Plate 107 CRD LH Front
161 Plate 107 CRD RH Front
162 Plate 107 CRD RH Side
163 Bolt
250 Washer 11/32 x 3/4 x 12 Ga.
- - Mandrel Assembly Tall (Includes Housing (key # 33), Shaft Assembly (key # 34), And Bearing Only (key # 19) - Pulley/Nut/Washer And Blade Bolt/Washers Not Included.)
- - Mandrel Assembly Short (Includes Housing (key # 45), Shaft Assembly (key # 124), And Bearing Only (key # 19) - Pulley/Nut/Washer And Blade Bolt/Washers Not Included.)
- - Replacement Mower Complete